innovaphone
IP29-2, IP29-4, IP29-8, IP311, IP411, IP511, IP811, IP0011, IP1130, IP3011

Delivery Contents

  • End device IP29-2, IP29-4, IP29-8, IP311, IP411, IP511, IP811, IP0011, IP1130, IP3011,
  • An accompanying document with QR code

Technical Data

Power supply:   PoE according to 802.3af, Class 3
Operation temperature:   0 °C to +45 °C
Storage temperature:   -10 °C to +70 °C
Humidity:   10% to 90% (non-condensing)

Intended Use

In line with the international standards H.323 or SIP, this device is suitable for connection to the innovaphone PBX or SIP server or other systems with comparable technology. The existing interfaces may only be used for appropriate purposes as follows:

Symbol   Use
BRI   RJ49C (Modular Jack 8P8C) connector for ISDN Basic Rate
PRI   RJ48C (Modular Jack 8P8C) connector for ISDN Primary Rate
FXO   RJ11C (Modular Jack 6P2C) connector for analogue trunk line
TEL   RJ11C (Modular Jack 6P2C) connector for analogue end devices
ETH   RJ45 (Modular Jack 8P8C) connector for Ethernet (LAN)

Warranty

Contact the specialist dealer in case of warranty. Improper use voids warranty.

Serial Number

The serial number and the hardware version for this device can be found underneath the device.

Declaration of Conformity

The company innovaphone AG, Umberto-Nobile-Straße 15, 71063 Sindelfingen, declares its sole responsibility that the products below comply with the basic requirements and other relevant provisions of the EMC directive 2014/30/EU and the RoHS directive 2011/65/EG when used properly. The following standards have been applied:

Product:

  • Analogue adapter innovaphone IP29-2 (Art. no. 01-00029-003)
  • Analogue adapter innovaphone IP29-4 (Art. no. 01-00029-004)
  • Analogue adapter innovaphone IP29-8 (Art. no. 01-00029-005)
  • VoIP gateway innovaphone IP511 (Art. no. 01-00511-001)
  • VoIP gateway innovaphone IP811 (Art. no. 01-00811-001)
  • VoIP gateway innovaphone IP3011 (Art. no. 01-03011-001)
  • VoIP gateway innovaphone IP1130 (Art. no. 01-01130-001)
  • VoIP gateway innovaphone IP0011 (Art. no. 01-00011-001)
  • VoIP gateway innovaphone IP411 (Art. no. 01-00411-001)
  • VoIP gateway innovaphone IP311 (Art. no. 01-00311-001)

Directives and standards applied:

  • EN 55022:2010
  • EN 55024:2010
  • EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + AC:2011 + A2:2013

Applies to IP511:

  • EN 55024:2010 + A1:2015
  • EN 55032:2015
  • EN 61000-4-2: 2009
  • EN 61000-4-3: 2006 + A1:2008 + A2:2010
  • EN 61000-4-4: 2004
  • EN 61000-4-5: 2006
  • EN 61000-4-6: 2009
 

Sindelfingen, 19.11.2020
Carsten Bode, Technical director

back

 USA / Canada

Delivery Contents

  • End device IP311, IP1130, IP3011,
  • An accompanying document with QR code

Technical Data

Power supply:   PoE according to 802.3af, Class 3
Operation temperature:   0 °C to +45 °C
Storage temperature:   -10 °C to +70 °C
Humidity:   10% to 90% (non-condensing)

Intended Use

In line with the international standards H.323 or SIP, this device is suitable for connection to the innovaphone PBX or SIP server or other systems with comparable technology. The existing interfaces may only be used for appropriate purposes as
follows:

Symbol   Use
BRI   RJ49C (Modular Jack 8P8C) connector for ISDN Basic Rate
PRI   RJ48C (Modular Jack 8P8C) connector for ISDN Primary Rate
FXO   RJ11C (Modular Jack 6P2C) connector for analogue trunk line
TEL   RJ11C (Modular Jack 6P2C) connector for analogue end devices
ETH   RJ45 (Modular Jack 8P8C) connector for Ethernet (LAN)

Warranty

Contact the specialist dealer in case of warranty. Improper use voids warranty.

Serial Number

The serial number and the hardware version for this device can be found underneath the device.

Industry Canada Warnings

This product meets the applicable Industry Canada technical specifications. The Ringer Equivalence Number (REN) is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination of an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices not exceed five. This product has a Ringer Equivalence Number of 0.2

FCC Compliance Statements

This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifi er in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.

IP311:   USOC Jack Type RJ11C
IP3011/IP1130:   USOC Jack Type RJ48C, Facility Interface Code 04DU9.1SN

 
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. The Ringer Equivalence Number (REN) or this terminal is 0.2
The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed fi ve (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifi er that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. If the device causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn‘t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to fi le a complaint with the FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, operations or procedures that could aff ect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifi cations to maintain uninterrupted service. If trouble is experienced with the device for repair or warranty information, please contact International Capital, LLC, 17130 Dallas Parkway, Suite 240, Dallas, TX, 75248, phone +1 (469) 687-2500. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.

Do NOT attempt to repair this equipment!

Connection to party line service is subject to state tariff s. Contact the state public utility commission, public service commission or corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of the device does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualifi ed installer. To avoid risk of fi re, use 26 AWG or higher wiring to connect the FXO telecom ports.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

Note:

This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna / Increase the separation between the equipment and receiver / Connect the equipment into an outlet on a circuit diff erent from that to which the receiver is connected / Consult the dealer or an experienced radio/TV technician for help.

back
Imprint | Contact | Policy | General Terms and Conditions | Privacy | WEEE | Notice on Cookies | | © 1997-2021 innovaphone AG

This website uses cookies to provide you with an optimal website experience. This includes cookies that are necessary for the operation of the website, as well as cookies that are only used for anonymous statistical purposes or for convenience settings to display special content. You can decide for yourself which settings you would like to allow. Please note that not all functionalities of the website might be available, depending on your settings. If you accept all cookies, you will have full access to all the services of our website. For further information, please read our privacy policy.

   
    Notice on Cookies